CEREC MTL Zirconia | Dentsply Sirona

global site

Do you want to change to Dentsply Sirona ?

Strong as ever. Beautiful like never before.

To achieve most perfect results in dental restoration, strength and beauty must go hand in hand. CEREC MTL Zirconia is the solution that provides you with strong, precise restorations that are highly esthetic and natural looking:

High Esthetics – natural multitransitional layer and high shade match.
High Strength - greater than 850 MPa¹ enable less reduction of the natural tooth.
Fast Zirconia Workflow - most efficient when using the CEREC Primemill & CEREC SpeedFire.
Easy Workflow – time saving and efficient.

CEREC MTL Zirconia mono

For fully anatomical anterior and posterior crowns, Inlays, Onlays, Veneers.

CEREC MTL Zirconia medi

For fully anatomical 3-unit anterior and posterior bridges.

Benefits

High Esthetics

Due to its high translucency and improved color matching characteristics, CEREC MTL Zirconia meets all esthetic needs.

High Strenghts

The high strength of > 850MPa of CEREC MTL Zirconia benefits both, dentist and patient. Restorative treatment is even possible in areas with limited space.

Easy Workflow

Time saving and efficient.

Fast Zirconia Workflow

Most efficient when using the CEREC Primemill & CEREC SpeedFire.

Instructions for Use

Click here to find manuals and more.

Go to IFU page

Natural Gradient for great Esthetics

Due to its high translucency and high color matching characteristics, CEREC MTL Zirconia meets all esthetic needs.
The excellent match with the most commonly used VITA classical Shade enables a most convenient color selection.
Natural Gradient: due to the Multitransitional layers of CEREC MTL Zirconia no layers are visible.

Color pigments
Translucency
CEREC MTL Zirconia with a seamless color gradient
Competitor material with 4 individual layers.

Strength for more confidence

The high strength of > 850MPa of CEREC MTL Zirconia benefits both, dentist and patient. Restorative treatment is even possible in areas with limited space.

CEREC MTL Zirconia is indicated for:

fully anatomical anterior and posterior crowns
fully anatomical 3-unit anterior and posterior bridges
Onlays
Inlays
Veneers

NOTE: For Super Fast Milling it is recommended to increase the minimum wall thickness to 0.7 mm.

Up to 40% lower
wall thickness and thus less natural tooth removal compared to competition for crowns allows for a more conservative preparation design and also provides greater flexibility on the restoration.²

of dentists say strenght is a primary reason for using zirconia.³

dentists fail to meet a 60-minute single-visit goal for their single-unit crown restorations, with long total processing times contributing to longer appointments.³

Fast Chairside Zirconia workflow

CEREC Primemill and CEREC SpeedFire for a fast CEREC MTL Zirconia workflow.

CEREC Primemill

With CEREC Primemill excellent CEREC MTL Zirconia crowns can be milled in around 5 minutes in the Super Fast milling mode.⁴

CEREC SpeedFire

With CEREC SpeedFire a crown can be sintered in 18 min. The optional glazing firing will take 9 min.

The CEREC MTL Zirconia workflow

Step 01:

Choose the block

In the CEREC SW 5.1.3 Material Pack single unit blocks (mono) and bridge blocks (medi) are included.

Choose the block that’s the best match for the case at hand.

Step 02:

Installing milling burs

If using CEREC Primemill in the Super Fast Mode, install the Bur 2.5 ZrO2 CS and Bur 1.0 CS on each side of the milling machine.

If using CEREC MC XL Premium Package, CEREC MC XL, CEREC MC X, install the burs Shaper 25 and Finisher 10.

Step 03:

Dust off milled crown

Use the large dusting brush to thoroughly remove any material residue that may have settled on the restoration during the milling process.

The surfaces of the crown must be clean and dust-free before sintering.

Step 04:

Sinter

In preparation for polishing and glazing, the crown must first be sintered with the CEREC SpeedFire furnace.

Manual programming is not required, as the CEREC SpeedFire furnace is preprogrammed for sintering CEREC MTL Zirconia.

Pro tip: For proper sintering, the crown must be placed upside down inside the furnace chamber.

Step 05:

Polish

CEREC MTL Zirconia can be finished by polishing or through a combination of polishing and glazing.

Ensure the restoration is properly polished, including the occlusal surface, especially of the areas that are in direct contact with the antagonist. After functional adjusting, re-polish the surfaces to achieve a high gloss.

This ensures potential unwanted abrasion while delivering a quality final restoration.

Step 06:

Apply firing paste (optional)

Fill the inside of the crown with just enough CEREC SpeedPaste to support the firing peg – do not overfill.

Push the crown gently onto a firing peg.

Step 07:

Glazing (Optional)

The restorations can be glazed with the DS Universal Stain and Glaze System or the DS Universal Spray Glazes (with or without Fluo)

Ensure the restoration is free of contamination and completely dried with oil-free air prior to paint-on or Spray Glaze application.

Pro tip: A little spray goes a long way (approx. 10 cm). Application of the spray glaze can be done over set, unfired stains.

Step 08:

Cementation pre-treatment

Prior to cementation of the crown, sandblast the internal surfaces in the one-way blasting process with maximum 50μm corundum (Aliuminiumoxide) at a pressure less than 2.5 bar.

Do not touch the sandblasted surface, if possible.

Step 09

Final cementation

For final cementation, apply Calibra Universal or Calibra Bio Cement according to the manufacturer’s directions for use.

Firing Recommendations

CEREC MTL Zirconia | Firing Recommendations

Firing recommendations for dry milling

Download

Downloads

CEREC MTL Zirconia | Order Information - SKU Overview | EN

List with all available CEREC MTL Zirconia items.

Download

Contact us for more information

Please contact us for more information about Restorative.

Footnotes

¹ 3-point bending strength

² Minimum Wall thickness for a posterior Katana Zirconia Block (Kuraray Nortiake) crown is 1.0 mm.

Minimum wall thickness for CEREC MTL Zirconia crown is 0.6 mm.

³ Data on file.

⁴ For Super Fast Milling it is recommended to increase the minimum wall thickness to 0.7 mm.

Strong as ever. Beautiful like never before.

CEREC MTL Zirconia mono

CEREC MTL Zirconia medi

Benefits

High Esthetics

High Strenghts

Easy Workflow

Fast Zirconia Workflow

Instructions for Use

Natural Gradient for great Esthetics

Strength for more confidence

Fast Chairside Zirconia workflow

CEREC Primemill

CEREC SpeedFire

The CEREC MTL Zirconia workflow

Step 01:

Choose the block

Step 02:

Installing milling burs

Step 03:

Dust off milled crown

Step 04:

Sinter

Step 05:

Polish

Step 06:

Apply firing paste (optional)

Step 07:

Glazing (Optional)

Step 08:

Cementation pre-treatment

Step 09

Final cementation

Firing Recommendations

CEREC MTL Zirconia | Firing Recommendations

Downloads

CEREC MTL Zirconia | Order Information - SKU Overview | EN

Related Products

Calibra Cements Family

CEREC Primemill

CEREC SpeedFire

Contact us for more information

Footnotes